How do you find a break in an invisible fence?

HTML format without tags:
![][1]

![][2]

![][3]

![][4]

![][5]

![][6]

![][7]

![][8]

![][9]

![][10]

![][11]

![][12]

![][13]

![][14]

![][15]

![][16]

![][17]

![][18]

![][19]

![][20]

![][21]

![][22]

![][23]

![][24]

![][25]

![][26]

![][27]

![][28]

![][29]

![][30]

![][31]

![][32]

![][33]

![][34]

![][35]

![][36]

![][37]

![][38]

![][39]

![][40]

![][41]

![][42]

![][43]

![][44]

![][45]

[1]: https://i.ytimg.com/vi/WDufU_qRINc/maxresdefault.jpg
[2]: #wpremark
[3]: #wpremark
[4]: #wpremark
[5]: #wpremark
[6]: #wpremark
[7]: #wpremark
[8]: #wpremark
[9]: #wpremark
[10]: #wpremark
[11]: #wpremark
[12]: #wpremark
[13]: #wpremark
[14]: #wpremark
[15]: #wpremark
[16]: #wpremark
[17]: #wpremark
[18]: #wpremark
[19]: #wpremark
[20]: #wpremark
[21]: #wpremark
[22]: #wpremark
[23]: #wpremark
[24]: #wpremark
[25]: #wpremark
[26]: #wpremark
[27]: #wpremark
[28]: #wpremark
[29]: #wpremark
[30]: #wpremark
[31]: #wpremark
[32]: #wpremark
[33]: #wpremark
[34]: #wpremark
[35]: #wpremark
[36]: #wpremark
[37]: #wpremark
[38]: #wpremark
[39]: #wpremark
[40]: #wpremark
[41]: #wpremark
[42]: #wpremark
[43]: #wpremark
[44]: #wpremark
[45]: #wpremark

















###

[1]: Begin your visual check at the transmitter, where you first see the wire above ground. Walk around the dog fence wire, give it a tug, see if it has tension or if it is loose. Follow the wire around your property and look for areas where they may have been twisted or chopped.

[2]: So that half an inch of copper wire is exposed on. Each. Then twist the two copper wire ends together grab an orange wire nut from the proper splice kit and twist it on until snug. Next grab the blue

[3]: Try searching between couch cushions or anywhere your dog likes to relax if the collar was lost after being removed indoors. If your pup is known for taking toys to their bed or favorite location, check there.

[4]: Begin to follow the twisted wire with the radio towards the main dog fence loop. You will begin to hear a combination of two sounds as you follow the twisted wire. Should there be a break in the twisted wire, the sound will slowly switch from two sounds to one sound.
Cached

[5]: So an electric fence isn’t hot a hundred percent of the time it’s only when you hear that clicking. So when you go to stick that piece of grass blade on there. And you’ll start filling the pulsing.

[6]: Here. And I have one here that I I put a break in it. So if we connect the positive and 1n connect the negative on the other. End. And on this one because there’s a break it’s showing the infinity.

[7]: If the electrical line is buried, dig at the half-way point. Use a voltage proximity detector or attach a voltage tester to the wire and test for voltage. If no voltage is read, the break is between the source and the half-way mark. Repeat testing by moving a few feet closer to the source until voltage is found.

[8]: The cost of each individual collar will range from $100 to $200, depending on the brand. Each animal will likely need training on the invisible fence as well, which will incur extra labor costs.

[9]: FitBark GPS Dog Tracker 2nd Gen (2022) | Health & Location Pet Tracking Smart Collar Device | 4G LTE Multi-Carrier Verizon, AT&T & T-Mobile US Coverage | Small (16 g) & Waterproof | iPhone & Android.

[10]: So we just lay this little tool on the hot wire and push the button 0.7 that is very low I’d like it to be between 7. Point one and eight point five even higher maybe but it is telling us that the

[11]: 1 inch to 3 inches
Most systems recommend that you bury the wires 1 inch to 3 inches underground. The wires don’t have to be underground to work, but if they’re aboveground, it’s easy to trip over them or to cut them with a lawnmower or trimmer. Test your wires aboveground before burying them.